Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Pacific Palisades Homeowners
Most chimney problems in Pacific Palisades start small and quiet: a hairline crack in the crown, a little mortar missing from a joint, a cap that’s lost its seal. Left alone through a few rainy seasons, those small faults let water into the masonry, and water is what turns a simple repointing job into a rebuild. We handle the full chimney system, from sweep and inspection through cap-and-crown work, firebox repair, and structural masonry. Our technicians have up to 11 years of experience, and we install professional-grade components from DuraFlex, HeatShield, Gelco, Famco, Olympia Chimney, and Copperfield rather than hardware-store substitutes. Same-day repair visits are often available in Pacific Palisades. Call (855) 531-2802. We answer 24/7.
What Our Chimney Repair Service Includes
Chimney repair covers the masonry, flashing, crown, and flue work that keeps your fireplace safe to burn. It’s distinct from a sweep, which removes creosote, and from an inspection, which tells you what condition the system is in. We inspect first and recommend second, so every repair we quote is tied to something we can show you. Here’s what each type of repair involves.
Mortar Repointing
Mortar repointing replaces the deteriorated mortar joints between bricks before the bricks themselves start to fail. You need it when joints have receded, turned chalky, or crumble when you touch them, which is common on older Pacific Palisades homes where original mortar has weathered through many dry seasons. We rake out the loose material to a proper depth and pack in fresh mortar matched to the original mix, so the repair holds and doesn’t damage the surrounding brick.
Spalling Brick Repair
Spalling is when a brick’s face flakes, peels, or pops off, usually because trapped moisture expands as it dries and pushes the surface away. You’ll notice brick fragments on the roof or a rough, pitted face on the chimney stack. We replace spalled bricks with sound masonry and address the moisture source behind them, because replacing brick without fixing what let the water in just delays the next round. Where a chimney has mild flue deterioration, HeatShield ceramic resurfacing can restore the flue lining without a full reline when conditions allow.
Chimney Waterproofing
Waterproofing means applying a breathable sealer to the masonry so rain runs off instead of soaking in, while moisture already inside can still escape as vapor. It’s the right call for a chimney that’s structurally sound but showing damp patches, efflorescence, or repeated spalling. In a mild climate like Pacific Palisades, the rainy season does the damage and the long dry stretch does the drying, so a breathable sealer matters more than a completely sealed surface. We apply it only after any masonry repairs are complete.
Flashing Repair
Flashing is the metal that seals the joint where the chimney meets the roof, and it’s the most common source of leaks people mistake for a chimney problem. You need flashing repair when you see staining on ceiling or framing near the chimney, rusted or lifted metal, or gaps where the flashing meets the masonry. We reset or replace the flashing and seal the seams so water runs onto the roof instead of behind it.
Chimney Rebuilding
Chimney rebuilding is for stacks that have gone past repair, where the upper courses are loose, leaning, or crumbling and repointing won’t hold. This typically happens when years of water intrusion have weakened the brick from the inside out, not just at the surface. We rebuild the affected section to match the existing masonry and tie in a properly formed crown so the new work is protected from the top down.
Tuckpointing
Tuckpointing is the finish work that shapes fresh mortar joints and can tint them to match the surrounding brick, giving a repaired chimney a clean, even look. It’s a natural companion to repointing when you want the repair to blend rather than stand out. We use it where appearance matters, such as a chimney on the front of the house, and to correct joints that have been poorly patched in the past.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We install and service DuraFlex flexible liner systems, the professional standard for relining an aging or damaged flue. DuraFlex matters on older Pacific Palisades homes where the original clay tile lining has cracked or separated, and it lets us bring a fireplace up to current safety performance without tearing out the whole stack. We also work with HeatShield ceramic flue resurfacing, which can repair a deteriorated liner from the inside when the existing structure is sound enough to support it.
On the cap and crown side we install Gelco chimney covers and Copperfield components, and we work with Famco venting products and Olympia Chimney systems where they fit the job. These are professional-tier brands, not the substitutes sold at big-box retail, and they hold up better to a full burn season. Whether your chimney has Olympia Chimney parts, Famco venting, or equipment from any other make, we can help.
Signs You Need Chimney Repair Right Now
Chimney damage tends to reveal itself through a handful of clear symptoms. If you notice any of these, get it looked at before your next fire, and definitely before the rainy season starts.
- Crumbling or missing mortar between bricks. Receded joints let water into the masonry and weaken the whole stack over time. Repointing early is far cheaper than rebuilding later.
- Flakes of brick on the roof or ground. This is spalling, and it means brick faces are breaking away. It’s a sign that moisture is getting in and forcing the surface off.
- Water stains on the ceiling or framing near the chimney. Staining usually points to failed flashing or a cracked crown, not the flue itself. Both are repairable once found.
- A cracked, loose, or missing chimney cap or crown. The crown sheds water off the top of the stack; when it cracks, water runs straight into the masonry. A damaged cap lets rain, animals, and debris in.
- A strong creosote smell or smoke spilling into the room. This can indicate a damaged or blocked flue and should be checked before you burn again. A trained professional should assess it, not a homeowner on a ladder.
Our Chimney Repair Process – Step by Step
Every repair starts with knowing exactly what’s wrong. Here’s how a job with us typically runs.
- 1
Inspection first. We examine the flue, firebox, damper, crown, cap, flashing, and masonry. Where the flue is involved, we run a camera so we can see the interior condition rather than guess at it.
- 2
Findings you can see. We show you what we found, with photos, and explain which problems are urgent and which can safely wait. Nothing gets recommended without evidence you can look at for yourself.
- 3
A written, flat-price estimate. You get the scope and the price in writing before any work begins, agreed before we book the job. The written estimate sets the final price.
- 4
The repair itself. We complete the masonry, flashing, crown, cap, or flue work with professional-grade materials, keeping the job contained and the workspace clean.
- 5
Final check. We verify the repair performs as intended, confirm the flue is clear and the draft is sound, and leave you with a clear record of what was done.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Pacific Palisades?
Chimney repair in Pacific Palisades typically runs from a few hundred dollars for a minor repointing job to several thousand for a partial rebuild, depending on how much masonry is involved and how far the damage has spread. The ranges below are typical estimates, not a firm quote, and the written estimate you receive sets the final price.
| Repair type | Typical estimated range | What drives the range |
|---|---|---|
| Mortar repointing or tuckpointing | $350 – $900 | Linear feet of joints, height of the stack, access |
| Spalling brick repair | $450 – $1,200 | Number of bricks replaced, extent of moisture damage |
| Chimney waterproofing | $300 – $700 | Masonry surface area, sealer coverage |
| Flashing repair | $400 – $1,000 | Roof pitch, flashing condition, sealant work |
| Partial chimney rebuilding | $2,000 – $6,000+ | Number of courses removed and rebuilt, cap and crown |
| Flue relining (DuraFlex) or resurfacing (HeatShield) | $1,800 – $5,000+ | Liner length, flue condition, system type |
Height and access matter a lot here. A tall stack or a steep roofline means more setup, and that’s often the largest swing in a quote. What keeps you from overpaying is an inspection-first approach: a masonry contractor who quotes a full rebuild without showing you camera evidence or a close look at the interior is asking you to take their word for it. We don’t work that way. Our free estimate includes a written scope and price, and we’ll tell you plainly when a problem can safely wait. Call (855) 531-2802 to book an estimate.
Chimney Repair Near Pacific Palisades – Our Service Area
We serve homeowners across Pacific Palisades and the surrounding Westside, including Santa Monica, Brentwood, Westwood, Venice, Mar Vista, Marina del Rey, Culver City, Beverly Hills, Topanga, Encino, and Tarzana. If you’re nearby and need Chimney Sweep Pacific Palisades, a repair, or a diagnostic visit, reach out and we’ll book you in for fast dispatch from 7am to 7pm, Sunday through Friday. Same-day repairs are often possible. We’re closed Saturday.
Serving Pacific Palisades, CA – Our Local Coverage Area
We serve Pacific Palisades and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Pacific Palisades
Chimney repair covers the masonry, flashing, crown, cap, and flue work that keeps your chimney structurally sound and fire-safe. It includes repointing mortar joints, replacing spalled brick, waterproofing, resetting flashing, rebuilding a damaged stack, and relining the flue. It’s separate from a sweep, which removes creosote, and from an inspection, which tells you what condition the system is in. If you need a cleaning, see our chimney repair service details and book a sweep alongside your repair.
Most minor repairs, like repointing a few joints or resetting flashing, take a day or less. A partial rebuild or a flue reline can take two to four days depending on access and weather. We give you a clear timeline with the written estimate, so you know what to expect before we start. Call (855) 531-2802 for an exact quote; estimates are free.
Chimney repair in Pacific Palisades typically costs $350 – $1,200 for mortar and brick work and $1,800 – $5,000+ for relining or a partial rebuild, depending on the scope. The written estimate sets the final price, and we agree the price with you before booking. Nothing gets added on after the fact. Call (855) 531-2802 for an exact quote; estimates are free.
Yes. We install and service DuraFlex flexible liner systems, HeatShield ceramic resurfacing, Gelco chimney covers, Copperfield components, and Famco and Olympia Chimney systems. Whether your chimney uses one of these or another make, we can assess it and recommend the right repair. If a full reline isn’t needed, we’ll tell you so. Call (855) 531-2802 to book a diagnostic visit.
Same-day repair visits are often available. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 531-2802 to book.
Repairs are backed by a workmanship warranty, and the specific terms are spelled out in your written estimate before the job is booked. We use professional-grade materials, so the repair is built to last rather than patched to pass a quick look. If something isn’t right after the work, we’ll make it right. Call (855) 531-2802 to learn more.
Clear the area around the fireplace and hearth, and make sure we can reach both the firebox and the roof access point. If you have pets, keep them away from the work area for the day. You don’t need to do anything else; we bring the tools and materials. If you’re also due for a cleaning, pairing it with your repair saves a second visit, and our chimney repair team serves neighboring areas the same way. Call (855) 531-2802 to schedule.
Schedule Your Chimney Repair Service in Pacific Palisades Today
If your chimney is showing cracks, loose mortar, spalling brick, or a damaged cap, get it looked at before the next burn season. Call (855) 531-2802 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. We inspect first, show you what we find, and price the job in writing. You’ll know exactly what needs fixing and what can wait. We also serve homeowners across the Westside, including our chimney repair coverage in Brentwood.
Written by the team at Chimney Sweep Pacific Palisades.